PACKING LIST
Package list
1.Scanner Body 2. Power Cable5 3. Power Adapter 4.Handle2 5.Memory Card Case 6.Manual 7.External GPS 8.USB-C to A Adapter 9.Memory Card Case 10.Handle Holder 11.D-Ring Mounting Screw
*The appearance of the product isn't standard across all specifications and editions. Product images are for illustrative purposes only!
*The memory card has been installed in the device before leaving the factory. The memory card case is only for storing the card.
Free stuff
*The free stuff can be used in scenarios such as vehicle-mounted mount, bicycle mount, backpack mount, or unmanned drone:
1.connecting plate 2. Knurled Thin Thumb Screw 3. Phillips head screw
a. Connect the connecting plate to the equipment using a Phillips head screw:
*The device does not come with a battery. After connection, an external power supply (power bank) is required to power the device. It is necessary to ensure that the output PD of the external power supply is greater than or equal to 45W. 
b. If you need to use vehicle-mounted mount, bicycle mount, backpack mount or unmanned drone, you can fix the bracket or drone to the connecting plate through a Phillips head screw and a Knurled Thin Thumb Screw (take the backpack bracket as an example).
For specific details, please refer to the corresponding operation instructions for the accessory bracket.
Scanner Components
*The power port is for connecting to an external power supply. (The connection to the handle is optional.)
Hardware Assembly
①Connect the handle holder to the handle using the ring screw.
Pass the D-Ring mounting screw through the screw hole on the handle holder first, pre-fix the handle on the holder, then tighten the screw at the bottom.
②Remove the silicone protective cover before usage.
*③Insert the memory card into the device through the bottom card slot.
(The memory card has been installed in the device before leaving the factory. It can also be removed if necessary.）
④Press the button on the handle to connect it to the device.
⑤Install the external GPS on the top of the device through the GPS interface.
Battery Charging
①Press the button on the handle to disconnect it from the device.
②Please follow the image to connect the cables.
- Please select the appropriate power cable according to actual conditions.
Before Scanning
Start Scanning
Data Export
Export the data with the provided USB drive or through a hotspot.
(*If the above methods do not work, you can export it with the card reader.)
Export using USB drive
Connect the USB drive with the adapter, and insert them into the device via data port.
Single Data Export
Batch Export
Export through a hotsopt
For detailed instructions, please refer to the following link:
Export using a card reader
Preparation Before Export
Please prepare your own card reader (USB 3.0 or USB 3.2 is recommended, with a read/write speed of 100MB/s).
When using the card reader to export data for the first time, if you cannot read the data in the data directory, please upgrade your device to the latest version first. After upgrading, you will also need to format the memory card (if there is scanning data on the device, it is recommended to export it first using a hotspot or USB drive before formatting, as formatting will erase all data).
Export
- Pull the memory card out from the bottom of the device and use your own card reader to transfer the data to your computer. Simply copy the data from the 'data' directory.
*The card reader shown is for reference only; please refer to the actual purchased product for use.
- After the export is complete, insert the memory card into the device and restart the device.
Upgrade to Latest Version
Preparing for Upgrade
- Download the latest firmware from our JMMeta community(https://forum.jimumeta.com/home/help/support.html)) to the USB flash drive and save it in the folder named upgrade.
Note: The upgrade folder needs to be created manually if there's no such folder in the USB.
- Turn on the device first, then connect the USB flash drive to the converter and insert it into the data transmission port of the device.
Upgrade
Import the Calibration File
The device has been calibrated before leaving the factory. If your device needs to be re-calibrated, please follow the steps below to re-import the calibration file.
Preparation before importing the file
- Enter the device SN number in the PC software and download the calibration file.
- Click the top right corner of the PC software to get the path of the calibration file, and download the corresponding calibration file to the U-drive in the 'calibration' folder (if this folder does not exist, you need to create a folder with this name first).
- Connect the USB flash drive to the adapter and insert them into the the device via data port.
Import
